The purpose of the piston is:
-the combustion pressure to convey on the connecting rod
-to ensure a gas-tight closure of the cylinder in relation to the
Carter. The gas-tight shut down the cylinder takes place using compression springs,
those in the top two (petrol engines) or three (in diesel engines)
piston ring grooves have been made. In the bottom piston ring groove is an oil scraper spring mounted. This need to
take care, that no more oil than strictly necessary for maintaining a lubricating film
between piston and cylinder of the outboard motor.
The Yamaha piston pin (Guide PIN) connects the piston swivel with the connecting rod "This is usually
made and secured by means of deposit floating feathers.
The Yamaha connecting rod provides the connection between piston and crankshaft. By
means of a bearing is the Yamaha connecting rod with the crankshaft connected.
The Yamaha crank put the up and down movement of the piston to
a circular motion. To the Yamaha as evenly as possible between crankshaft
the labour succeed in running is to keep a flywheel
Tailpiece parts for all Yamaha outboard models. All Yamaha tailpiece parts are very easy by per model filed under the drawing. Did you know that tail piece parts in English Lower unit parts means?
Power Watersports supplies impeller kit of high quality and that is why we give also a year warranty on all Yamaha impeller kits!
Also the supply is good. For shipping within the Netherlands you pay only from €6.95 and for shipping to the rest of the EU from €8.95. From an order amount of €100 is the shipping free. The delivery is done through recognized carriers such as GLS.
Power Watersports supplies high quality starter motors and therefore we also give a one year warranty on all Yamaha starters!
Power Pack, spark plugs, ignition coil, Stators for the Yamaha outboard motor
A throttle cable can break as soon as it is worn out or overdue maintenance. The throttle of outboard motor should be greased every year. These fats can be found at maintenance outboard engine.
All throttle cables are here to find and you can easily find online with original throttle cable part number.
These are original Solas boat propellers van gehard staal en aluminium! Wij zijn distributeur van SOLAS boat screws (Solas Marine Netherlands).
If the outboard, or not to correct RPM comes from inboardmotor bv. 5700 rpm 6000 rpm and the engine makes but then it is advisable to one pitch to go up. When too much rows of bv. 6300 rpm it is advisable to have one pitch down.
All petrol plugs and fuel plugs are available from stock.
A head gasket is een afdichting die zich bevindt tussen de cilinderkop en het motorblok.
By aging or overheating and use exhibits a head gasket wear, so after much use replacement will be necessary. The most common leak is that between the cylinder and the cooling water slot. A leaky head gasket can have different effects of small oil leakage, less power due to lower compression to cooling water loss and overheating. A leaky head gasket is rather common, in both gasoline and diesel engines and regardless of the manufacturer of the engine.
Replacement is easy in theory, but in practice, especially in modern Yamaha outboard motors quite some time, because many parts have to be removed, for the cylinder head can be kept. Especially with the modern Yamaha injection engines is that the case. The cost for a repair for more than 95% are in labor. The head gasket yourself often costs but a few tens of euros, so better do it yourself and purchase a repair manual. The cylinder head bolts should be tightened with a torque wrench, in multiple steps and in an order specified by the manufacturer.
A Yamaha crankshaft axis via a connecting rod connected to the Pistons moving up and down. As the piston moves the stool of the crankshaft is pushed up and goes the crankshaft turning. There are countless shapes and sizes, depending on the application and the manufacturer and sometimes a crank not even recognizable as such because it also can be mounted. The crankshafts of Yamaha outboard motors for example look completely different than that of a inboardmotor.
A crank is an important outboard part in almost everything a motorized movement. The axle must be performed very carefully because there are large forces on. In addition, some cranks a very high rotation speed leaving a small (such as a curve crankshaft) construction or Assembly error can lead to lockups.
All original paint spray cans available online here
The fuel pump for your Yamaha outboard motor is necessary to the fuel from the tank to the outboard motor. Depending on the fuel there are diesel and petrol pumps. Fuel pump is located on the engine block. There are many fuel pump models for Yamaha outboard motors.
Defects at Yamaha fuel pumps are often met. The wear can lead to mechanical damage. You can detect a mechanical damage by a loud noise (electric fuel pumps). If the problems appear when the outboard motor is warmed up, this confirms that the pump is damaged, because the pressure falls away after you the engine with a damaged pump outlet. Very often the fuel filter clogged there is a problem with intake manifold. Pump function can be checked with a manometer.